Quick Info :
Operating voltage:5V (supplied from the Arduino Board)
Ethernet Controller: W5500 with internal 32K buffer
Connection speed: 10/100Mb
Connection with Arduino on SPI port
Rs 4,390.00
Quick info :
Operating voltage: 6 – 30V DC
1 Channel delay triggered relay module
Delay time: 0.1 second to 999 minutes
Rs 590.00
Quick info :
Product model: ZK-MT21
Bluetooth-compatible version: 5.0
Input sensitivity: 500mV
Input method: AUX+ Bluetooth-compatible
Number of channels: 2.1 channels
Power amplifier chip: Domestic power amplifier chip
Adapter power supply: above DC12-24V/5A (24V battery pack is not allowed)
Adapted speakers: 20-100W, 4-8Q
Output power: left and right channels <50W; subwoofer <100W
Rs 4,500.00Rs 4,890.00
Quick Info :
Channels : 1
Input release voltage: 3.5 to 5V
Rated load voltage: 100V to 240V AC
Load current: 0.10 to 2A
Rs 600.00
Specification:
Size: 1.28inch
Resolution: 240 × 240
Driving chip: GC9A01
Interface method: SPI
Color: Full-color RGB
Rs 2,190.00
Quick info :
Display Size: 1.8″
Driver IC: ST7735
Input Voltage (V): 3.3 to 5
Pixel Resolution: 128 x 160
Interface Type: SPI
Rs 1,490.00
Quick info:
Plug-and-Play: Easy setup with USB 2.0 interface
Compatibility: ISO 14443 Type A/B, ISO 15693, and NFC cards
Data Transfer speed: 106 kbps, 212 kbps, and 424 kbps
Power Supply: 5V DC
Rs 2,100.00
Quick Info :
Support Card Type: Read-only ID card (EM4100, IM4001)
Support frequency: 125KHz
Reader Time: <0.2s
Read Range: 3-10cm
Rs 990.00
Quick Info
Operating Voltage : 9 – 12 V (Preferred 12V)
Case (L x W x H) : 53 x 40 x 28mm (2.1 x 1.6 x 1.1″)
Latch (L x W) : 10 x 10mm (0.4 x 0.4″)
Rs 1,590.00
Quick Info :
Material: ABS
Dimension(LxWxH): 43.7×30.5×5.3mm
Response Frequency: 13.56MHz
Chip type: FM1108 Fudan Chip
Rs 100.00
Quick Info :
16 Channel
Maximum switching voltage: 250VAC / 30VDC
Maximum switching current: 10A
Module operating voltage: 5V
Rs 2,950.00
Quick Info :
Channels : 2
Input release voltage: 3.5 to 5V
Rated load voltage: 100V to 240V AC
Load current: 0.10 to 2A
Rs 1,150.00
Quick Info :
240*320 pixels
Suitable for an Uno (Atmega328P) or Mega (Atmega2560) based Arduinos (other chips are not supported)
Dimensions: 72.5 mm x 53 mm
Driver: ILI9320 or ILI9341 (or compatible with one of two)
Rs 2,250.00
Quick Info :
Channels : 4
Input release voltage: 3.5 to 5V
Rated load voltage: 100V to 240V AC
Load current: 0.10 to 2A
Rs 1,600.00
Quick Info :
Transmitter PCB Supply Voltage : 3V
Receiver PCB Supply Voltage : 4.5V to 6V
Working range: 40m – 50m
Rs 1,390.00
Quick info :
Operating voltage: DC12V;
Operating current: <20MA;
Operating frequency range: 20Hz ~ 400Hz;
Output mode: switch signal output;
Maximum detection wire diameter: 5.2mm;
Rs 950.00
Quick Info :
Channel : 8
Coil sensitivity = 5VDC
Maximum Contact capacity = 250VAC/10VDC
Maximum Current capacity = 10A
Rs 1,400.00
Quick Info :
Frequency – 1559Mhz-1609Mhz
Active antenna noise figure < 1.5dB
Cable – RF1.13
Connector – I-PEX
Rs 650.00
Quick Info :
WIDE SUPPLY RANGE: 2.0V to 5.5V
PROGRAMMABLE DATA RATE: 8SPS to 860SPS
Rs 1,750.00
Quick Info :
Real Time Clock Module : DS1307
SD Card reader : standard SD card
RTC battery included
Rs 690.00
Quick Info:
Onboard chip AT24C256 chip
Onboard the I2C communications required pull-up resistor
All pins are leads and marked
PCB board Dimensions : 36.5 (mm) x12 (mm)
Rs 390.00
Quick Info :
Stackable design, easy to plug into the ARDUINO development board.
Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
Coupled with the XBee module, you can achieve two or more sets of communication between Arduino or Arduino and PC Communications.
Rs 750.00
Quick Info :
A single module can drive a total of 8 * 8 dot matrix overcast
The module voltage: 5V
Module Size: 12.8 cm (length) X 3.2 cm (width) X 1.3 cm (height)
Rs 1,650.00
Quick Info :
Perfect for experimentation and prototype work
Brings all 9 pins of a DB9 connector to screw terminal blocks
Adapter used for communication debug
9 pcs signal line was all lead out, name and number clearly labeled;
Rs 290.00
Quick Info :
Module Size: 2.8cm * 1.3cm
Applicable connector: 5.5 * 2.1mm
Power output interface: 2 channel VCC, 2 channel GND
Net Weight: 3.2g
Rs 100.00
Quick Info :
Input Voltage: 6 ~ 27V
Driver: Dual BTS7960 H Bridge Configuration
Peak current: 43-Amp
Rs 1,490.00
Quick Info :
Max. Operating Voltage: 45 V
Min. Operating Voltage: 8.2 V
Max. Current Per Phase: 2.5 A
Alternatives for DRV8825 : A4988 , TMC2209
Rs 590.00
Quick Info
Supply voltage (typically): 3.3V
Battery not included
Battery : CR2032
Rs 790.00
Quick Info :
Operating voltage : 2.3V – 5.5V
Battery not included
Battery : CR2032
Rs 590.00
Specifications :
Input Voltage: 220V
Maximum Power: 2000W
Adjustable Voltage: 50V-220V
Rs 950.00Rs 1,250.00
Quick Info :
ENC28J60 Ethernet chips, SOP28 package
SPI Interface
Single Supply: +3.3 V
Rs 990.00
