Quick Info :
Max. Operating Voltage: 35V
Min. Operating Voltage: 8V
Max. Current Per Phase: 2A
Alternatives for A4988 : DRV8825 , TMC2209
Rs 390.00
Quick Info :
Compatible with standard Arduino and Arduino Mega
Selectable interface between hardware serial port and software serial port
Support TCP/UDP protocols
Rs 4,100.00
Quick Info :
Operating voltage:5V (supplied from the Arduino Board)
Ethernet Controller: W5500 with internal 32K buffer
Connection speed: 10/100Mb
Connection with Arduino on SPI port
Rs 4,390.00
Quick Info :
Voltage: 3-3.6V (recommended 3.3V) V.
Maximum output power: +20dBm.
Power-down mode current: 4.2uA.
Operating Range: 1Km
Rs 950.00
Quick Info :
It can be used with NRF24L01 wireless module
Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
Allows for easy connection to nRF24L01+ modules
Small power on SMD LED indicator
Rs 250.00
QUICK OVERVIEW
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability,
Built-in hardware CRC error detection, Multipoint communication address control.
Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
Built-in 2.4Ghz antenna
Built-in voltage regulator
Rs 490.00
Quick Info :
Bluetooth v2.0+EDR
2.4GHz ISM band frequency
Default baudrate: 9600
Power supply: 3.6V to 6V DC
Rs 1,090.00Rs 1,350.00
Quick Info:
Bluetooth v2.0+EDR
2.4GHz ISM band frequency
Supported baud rate: 9600 (default), 19200,38400, 57600, 115200, 230400, 460800.
Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
Power supply: 3.6V to 6V DC
Rs 1,090.00Rs 1,350.00
Quick Info :
802.11 b/g/n
Operating Voltage: 3.3V
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Rs 590.00
Quick Info :
Transmitter Operating Voltage: +5V only
Transmitter Operating current: 9mA to 40mA
Operating frequency: 433 MHz
Transmission Distance: 3 meters (without antenna) to 100 meters (maximum)
Rs 390.00
Quick Info :
MFRC522 chip based board
Operating frequency: 13.56MHz
Supply Voltage: 3.3V
Current: 13-26mA
Rs 590.00
Quick Info :
Operating voltage : 2.3V – 5.5V
Battery not included
Battery : CR2032
Rs 590.00
Quick Info:
Onboard chip AT24C256 chip
Onboard the I2C communications required pull-up resistor
All pins are leads and marked
PCB board Dimensions : 36.5 (mm) x12 (mm)
Rs 390.00
Quick Info :
All SD SPI pins output, MOSI, SCK, MISO, and CS.
Support 5V/3.3V input.
This module can handle 2GB SD cards.
Rs 350.00
Quick Info:
Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Size: 45 x 28mm
Net weight: 6g
Rs 350.00
Quick Info :
Acrylic Body.
Easy to install.
Compatible with HC-SR04
Rs 190.00
Quick Info :
Name: TT motor
Type: 1:48
Speed: 45±10%r/min 90±10%r/min
Rated voltage: 3V/6V
Rs 350.00
Quick Info :
Channels : 2
Input release voltage: 3.5 to 5V
Rated load voltage: 100V to 240V AC
Load current: 0.10 to 2A
Rs 1,150.00
Quick Info :
Channel : 4
Coil sensitivity = 5VDC
Maximum Contact capacity = 250VAC/10VDC
Maximum Current capacity = 10A
Rs 790.00
Quick Info :
Channel : 1
Coil sensitivity = 5VDC
Maximum Contact capacity = 250VAC/10VDC
Maximum Current capacity = 10A
Rs 250.00Rs 390.00
Quick Info :
Arduino and Raspberry Pi compatible
16-key membrane switch pad has 8 pin female header on end of flat cable
White sticker on back can be peeled off for adhesive mounting
Rs 290.00
Quick Info :
Interface : I2C
I2C Address : 0x3F
Supply voltage : 5V
Contrast Adjust : Through Potentiometer
Backlight : Blue
Rs 1,100.00
Quick Info :
OLED Driver IC: SSD1306
Resolution: 128 x 64
Visual Angle: >160°
Input Voltage: 3.3V ~ 6V
Compatible I/O Level: 3.3V, 5V
Rs 750.00Rs 990.00
Quick Info :
A single module can drive 8 by 8 common cathodes
Module Operating voltage: 5V.
Module size: 5 cm long X 3.2 cm wide X 1.5 cm high
Module with input and output interfaces, supports multiple modules cascade
Led colour:Red
Rs 800.00
Quick Info :
Operating Voltage: 5V
Backlight and Contrast is adjusted by potentiometer
Compatible for 16×2 , 16×4 and 20×4 LCD
Rs 250.00Rs 390.00
Quick Info :
Operating Voltage is 4.7V to 5.3V
Current consumption is 1mA without backlight
Alphanumeric LCD display module, meaning can display alphabets and numbers
Consists of two rows and each row can print 16 characters.
Compatible with LCD to I2C Adapter Board
Rs 460.00 – Rs 490.00
Quick Info :
Size: 48mm x 29mm x 26mm.
Display color: Red & Blue LED (dual display).
Display: 0.28″ LED digital.
Operating voltage: DC 4.5 ~ 30V.
Measure voltage: DC 0 ~ 100V.
Measure current: 10A (direct measurement, built-in shunt).
Rs 690.00
Quick Info :
USB Type : Micro USB
Header : 2.54mm
Material : Plastic
Size(L*W) : Approx. 26.06 x 22.93mm
Rs 100.00