Converter
Interface converters: logic level shifters, USB to TTL and RS485 adapters, CAN modules, ADC and DAC boards, I2C multiplexers and breakout adapters.
-
MCP23017 16 Bit I2C/SPI IO Expander Module
Quick Info:
- Chip : MCP23017 / MCP23S17
- IO Pins : 16 (Bidirectional)
- Interface : I2C / SPI
- SPI Speed : Up to 10MHz
- Operating Voltage : 1.8V to 5.5V
Rs 1,550.00Rs 1,800.00MCP23017 16 Bit I2C/SPI IO Expander Module
Rs 1,550.00Rs 1,800.00 -
ADUM1201 Magnetic Isolator Module CJMCU-1201
Quick Info:
- Chip : ADUM1201
- Channels : 2 (Bidirectional)
- Data Rate : DC to 25Mbps
- Isolation Voltage : 2500Vrms
Rs 490.00Rs 550.00ADUM1201 Magnetic Isolator Module CJMCU-1201
Rs 490.00Rs 550.00 -
TXS0108E 8CH Logic Level Converter 1.2V to 5.5V
Quick Info:
- IC : TXS0108E
- Channels : 8 (all bi-directional, full-duplex)
- VCCA (A side) : 1.2V – 3.6V (low voltage)
- VCCB (B side) : 1.65V – 5.5V (high voltage)
- Max Speed (Push-Pull) : 110Mbps
- Max Speed (Open-Drain) : 1.2Mbps
- Direction Sensing : Automatic (no DIR pin)
- Protocols : UART / SPI / I²C / GPIO / SD card
- Pin Pitch : 2.54mm breadboard compatible
- Compatible : Arduino / ESP32 / Raspberry Pi / STM32
Rs 180.00Rs 220.00TXS0108E 8CH Logic Level Converter 1.2V to 5.5V
Rs 180.00Rs 220.00 -
PC817 Optocoupler Isolation Board 3.6-30V
Quick Info:
- Optocoupler Type : PC817
- Drive Signal Voltage : 3.6V – 24V
- Output Voltage Range : 3.6V – 30V
- Output Logic : Jumper Configurable
Price range: Rs 350.00 through Rs 950.00 -
MEGA2560 Prototype Screw Terminal Shield Kit
Quick Info:
- Compatibility : Arduino Mega 2560 R3
- PCB Type : Double-Sided FR-4
- Terminal Block Pins : 84 Total
- Wire Range : 26–16 AWG
Rs 1,950.00Rs 2,100.00MEGA2560 Prototype Screw Terminal Shield Kit
Rs 1,950.00Rs 2,100.00 -
PIC K150 USB Microcontroller Programmer
Quick Info:
- Interface : USB
- Programming Socket : 40-pin DIP (ZIF)
- Supported Chips : PIC10 / PIC12 / PIC16 / PIC18
- Power Source : USB (no external supply)
Rs 2,550.00Rs 2,900.00PIC K150 USB Microcontroller Programmer
Rs 2,550.00Rs 2,900.00 -
PICkit3 PIC Programmer Debugger with Adapter
Quick Info:
- Interface : USB (Full Speed)
- Programming Protocol : ICSP
- Supported Devices : PIC10/12/16/18/24, dsPIC
- Included Accessory : ICSP Adapter Board
Rs 5,650.00Rs 6,250.00PICkit3 PIC Programmer Debugger with Adapter
Rs 5,650.00Rs 6,250.00 -
USB 2.0 to RS232 Serial Converter Cable
Quick Info:
- PC Interface : USB 2.0 Type-A Male
- Device Interface : DB9 Male (RS232)
- Data Transfer Rate : Up to 921.6Kbps
- OS Support : Windows / macOS / Linux
- Cable Length : Approximately 1 metre
- Bus Powered : Yes (5V USB)
- Plug and Play : Yes
Rs 1,580.00Rs 1,700.00USB 2.0 to RS232 Serial Converter Cable
Rs 1,580.00Rs 1,700.00 -
USB to RS485 Converter Module Waveshare vB
Quick Info:
- Brand : Waveshare
- Host Interface : USB Type-A
- Device Interface : RS485 Screw Terminal
- Baud Rate : 300bps – 921600bps
- Transmission Distance : Up to 1200 metres
- Power Supply : USB Bus Powered (5V)
- OS Support : Windows / Linux / macOS
- Direction Control : Automatic
Rs 3,250.00Rs 3,550.00USB to RS485 Converter Module Waveshare vB
Rs 3,250.00Rs 3,550.00 -
ST-Link V2 Programmer & Debugger
Quick Info:
- Compatible MCUs : STM8 & STM32 Series
- Protocols : SWIM, SWD, JTAG
- Host Interface : USB 2.0 Type-A
- Power Supply : Bus-Powered via USB
- Compatible IDEs : STM32CubeIDE, Keil, IAR
- Operating System : Windows, Linux, macOS
Rs 690.00Rs 725.00ST-Link V2 Programmer & Debugger
Rs 690.00Rs 725.00 -
CH341B EEPROM Programmer Kit 3.3V/5V
Quick Info:
- Programmer IC : CH341B
- Supported Voltage : 1.8V / 3.3V / 5V
- Supported Chips : 24Cxx / 25Cxx EEPROM
- Clip : SOIC8 / SOP8 Test Clip
- Adapter : SOP8 to DIP8 Converter
- Interface : USB
Rs 2,850.00CH341B EEPROM Programmer Kit 3.3V/5V
Rs 2,850.00 -
SOIC 8 SOP8 to DIP8 Converter Module
Quick Info:
- Compatible Package : SOIC-8 / SOP8
- Output Format : DIP-8
- SMD Pad Pitch : 1.27mm
- DIP Pin Pitch : 2.54mm
- PCB Material : FR4
- PCB Dimensions : 19mm x 14mm (approx.)
- Surface Finish : HASL
Rs 50.00Rs 80.00SOIC 8 SOP8 to DIP8 Converter Module
Rs 50.00Rs 80.00 -
USB 3.0 Card Reader SD/TF
Quick Info:
- Interface : USB 3.0
- Supported Cards : SD, TF (MicroSD)
- Transfer Speed : Up to 5 Gbps
- Compatibility : Windows, macOS, Linux
- Driver Required : No (Plug and Play)
- Power : Bus Powered via USB
Rs 850.00Rs 950.00USB 3.0 Card Reader SD/TF
Rs 850.00Rs 950.00 -
DVI to HDMI Converter Adapter Module
Quick Info :
- Type: DVI-D ↔ HDMI passive adapter
- Direction: Bidirectional
- Resolution: Up to 1080p Full HD
- Audio: Not supported
- Power: None required (passive)
- Compatible: PC, Raspberry Pi, monitors, projectors
- Signal: Digital video only
Rs 550.00Rs 650.00DVI to HDMI Converter Adapter Module
Rs 550.00Rs 650.00 -
SSOP 16PIN/SOP 16PIN to DIP Adapter PCB Module
Quick Info :
- Input: SSOP-16 / SOP-16 SMD packages
- Output: DIP-16 (2.54mm pitch)
- SSOP Pitch: 0.635mm
- SOP Pitch: 1.27mm
- PCB: FR4, 1.6mm thickness
- Compatible: Breadboards, DIP sockets
- Use: SMD to through-hole conversion
Rs 50.00Rs 80.00SSOP 16PIN/SOP 16PIN to DIP Adapter PCB Module
Rs 50.00Rs 80.00 -
QFP100 to DIP100 Adapter Programming Socket
Quick Info :
- Type: QFP to DIP Adapter Socket
- Package: QFP100/TQFP100/LQFP100
- Pin Pitch: 0.5mm
- IC Size: 14×14mm body
- Output: DIP100 (2.54mm pitch)
Rs 7,500.00Rs 7,900.00QFP100 to DIP100 Adapter Programming Socket
Rs 7,500.00Rs 7,900.00 -
Logic Level Converter Bi-Directional Module 8 Channel
Quick Info :
- Type: Bi-Directional Level Shifter
- Channels: 8 Independent
- Voltage: 5V ↔ 3.3V
- Speed: Up to 400kHz
- Applications: I2C, SPI, UART, GPIO
Rs 320.00Rs 450.00Logic Level Converter Bi-Directional Module 8 Channel
Rs 320.00Rs 450.00 -
USB Type C to DIP Adapter PCB Module
Quick Info :
- Connector : USB Type-C
- Output Type : DIP 2.54 mm
- Use Case : Breadboard & PCB Prototyping
- Material : FR-4 PCB
Rs 120.00Rs 250.00USB Type C to DIP Adapter PCB Module
Rs 120.00Rs 250.00
Modules that let two different systems talk to each other: bi-directional 5V to 3.3V logic level converters, USB to TTL serial adapters (FT232RL, CP2102, CH340G), MAX485 and USB to RS485 converters, CAN modules (MCP2515, SN65HVD230), ADS1115 and HX711 analog-to-digital converters, the TCA9548A I2C multiplexer and SOIC, USB and ESP32 breakout boards.
Which converter do I need?
To program a board that has no USB port, or to read a serial device on a PC, use a USB to TTL converter. To connect a 5V sensor to a 3.3V ESP32 or Raspberry Pi, use a logic level converter. For long cable runs between devices, RS485 or CAN is far more reliable than plain serial. To read precise analog values, add an ADC module.