Quick Info :
Length: 5 inches (125mm)
Blade Material: Hardened Carbon Steel / Stainless Steel
durable blades for clean and accurate cuts.
Made from high-quality materials for long-lasting performance.
Flush-cut or semi-flush (for clean, precise cuts)
Rs 690.00
Quick info :
Output Power: 2x50W (stereo mode) or 100W (mono mode)
Frequency Response: 20Hz to 20kHz
Signal-to-Noise Ratio (SNR): ≥100dB
Chip: TPA3116D2
Power Supply Voltage: 12-24V DC
Rs 690.00
Quick Info :
Operates with a single 3.3 V Supply
Bus Pin ESD Protection Exceeds ±16 kV HBM
High Input Impedance Allows for Up to 120 Nodes on a Bus
Rs 690.00
Quick Info :
Sensing distance : 5mm
Operating voltage : 10 – 30 VDC
Response frequency : 800Hz
Output method : PNP, 150mA load
Rs 690.00
Quick Info :
Size (L x B x H) : 15 cm x 5 cm x 2 cm Weight : 100 g Size : 6 Inch
Rs 690.00
Quick Info :
Real Time Clock Module : DS1307
SD Card reader : standard SD card
RTC battery included
Rs 690.00
Quick Info :
Dimensions: 115mm X 90mm X 55mm
Rs 690.00
Quick Info :
CPU Speed : 20MHzProgram Memory Size : 8KBRAM Memory Size : 512ByteNo. of Pins : 8 Pins
Rs 690.00
Quick Info :
Input Voltage: 5-35V
Input Voltage Must Be At Least 2V Above Output Voltage
Output Voltage: 1.25-30V (infinitely adjustable)
Constant Current Range: 0-3A (infinitely adjustable)
Rs 690.00
Quick Info :
Frequency – 1559Mhz-1609Mhz
Active antenna noise figure < 1.5dB
Cable – RF1.13
Connector – I-PEX
Rs 650.00
Quick Info :
Operating Voltage: 12V DC
Module Dimensions: 5cm x 2.7cm x 2cm
Sensor: Photosensitive resistance module
Rs 650.00
Quick Info :
Brand: R’DEER
Model: RT-125F
Size: 5 inches (125mm)
Material: High-carbon steel with plastic-coated handles
Stripping sizes ranging from AWG 30 to 10
Cutting small wires and cables.
Rs 600.00
Quick Info :
Operating Voltage: 5V
5 Push buttons.
Left, Right, Up, Down and Select buttons
Screen contrast adjustment
Arduino Reset button
Rs 595.00
Quick Info :
Impedance: 6 Ω
Rated Power Handling: 15 W
Magnet type : Double Magnet
Frequency Response: 108 Hz – 20 kHz
Speaker Diameter: 3 inches (78 mm)
Mounting Depth: 52 mm
Rs 590.00
Quick Info :
Dimensions: 80mm X 80mm X 60mm
Rs 590.00
Quick Info :
LED Peak Wavelength: 660nm/880nm
LED Supply Voltage: 3.3~5V
Interface: I2C Interface
Operating Temperature Range: -40°C to +85°C
Rs 590.00
Quick Info :
Power requirements : VCC – 5V±0.1
DO output : TTL digital 0 and 1 (0.1 and 5V)
AO output : 0.1-0 .3 V (relative to pollution), the maximum concentration of a voltage of about 4V
Detection Gas: Carbon Monoxide
Rs 590.00
Quick Info :
Operating voltage : 2.3V – 5.5V
Battery not included
Battery : CR2032
Rs 590.00
Quick Info :
Eight 7-Segment LED Displays with 0.36″ high red digits
LED displays mounted in sockets
Built-in MAX7219 LED Driver
SPI 3-wire serial interface for easy hookup to MCU
Can daisy-chain multiple modules together for larger displays
Rs 590.00
Quick Info :
Simple 3 pin interface to control the resistance
Supply voltage: 3V-5V
Chip: X9C103S
PCB board size: 2.7 * 1.3CM
10K span potentiometer.
Rs 590.00
Quick Info :
Resolution 640×480 VGA
Flicker (50/60 Hz) auto detection
Onboard regulator, only single 3.3V supply needed
Rs 590.00Rs 925.00
Quick Info:
Working voltage: 6 to 18V
Dual channel 15W+15W
on-board dial potentiometer
Rs 590.00
Quick Info :
Input Voltage : AC 100 ~ 240V 50/60 HZ
Output Voltage: DC 12V
Output Current: 1A
Plug Type : UK Plug
Rs 580.00
Quick Info :
1pc screwdriver handle
1pc 4 inch rod
Sizes:
Slotted: Ø0.8, Ø1.2, Ø2.0, Ø2.5, Ø3.0, Ø4.0
Phillips: PH000, PH00, PH0, PH1, PH2
Torx: T4, T5, T6, T8, T10
Hex: Ø0.7, Ø0.9, Ø1.5, Ø2.0, Ø2.5, Ø3.0
Pentalobe: Ø0.8, Ø1.2 U-Type: U2.3, U3.0
Triangle: 2.0, 3.0
Y-Type: Y2.0
Other: Ø0.5, Ø0.3, Ø0.35
Rs 550.00
