Quick Info :
Max. Operating Voltage: 35V
Min. Operating Voltage: 8V
Max. Current Per Phase: 2A
Alternatives for A4988 : DRV8825 , TMC2209
Rs 330.00
Quick Info :
Compatible with standard Arduino and Arduino Mega
Selectable interface between hardware serial port and software serial port
Support TCP/UDP protocols
Rs 4,100.00
Quick Info :
Complies with wireless 802.11n standards
Frequency band: 2.4~2.4835GHz
Data rate up to 150Mbps
Rs 1,250.00Rs 1,450.00
Quick Info :
Operating voltage:5V (supplied from the Arduino Board)
Ethernet Controller: W5500 with internal 32K buffer
Connection speed: 10/100Mb
Connection with Arduino on SPI port
Rs 4,390.00
Quick Info :
Quad-band 850/900/1800/1900MHz – connect onto any global GSM network with any 2G SIM
Send and receive SMS messages.
Send and receive GPRS data (TCP/IP, HTTP, etc.).
Scan and receive FM radio broadcasts.
Minimum Power supply required : 5v 2A Power Supply
Rs 2,390.00
Quick Info :
Voltage: 3-3.6V (recommended 3.3V) V.
Maximum output power: +20dBm.
Power-down mode current: 4.2uA.
Operating Range: 1Km
Rs 950.00
Quick Info :
It can be used with NRF24L01 wireless module
Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
Allows for easy connection to nRF24L01+ modules
Small power on SMD LED indicator
Rs 250.00
QUICK OVERVIEW
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability,
Built-in hardware CRC error detection, Multipoint communication address control.
Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
Built-in 2.4Ghz antenna
Built-in voltage regulator
Rs 490.00
Quick Info :
Bluetooth v2.0+EDR
2.4GHz ISM band frequency
Default baudrate: 9600
Power supply: 3.6V to 6V DC
Rs 1,090.00Rs 1,350.00
Quick Info:
Bluetooth v2.0+EDR
2.4GHz ISM band frequency
Supported baud rate: 9600 (default), 19200,38400, 57600, 115200, 230400, 460800.
Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
Power supply: 3.6V to 6V DC
Rs 1,090.00Rs 1,350.00
Quick Info :
802.11 b/g/n
Operating Voltage: 3.3V
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Rs 590.00
Quick Info :
ENC28J60 Ethernet chips, SOP28 package
SPI Interface
Single Supply: +3.3 V
Rs 990.00
Quick Info :
Transmitter Operating Voltage: +5V only
Transmitter Operating current: 9mA to 40mA
Operating frequency: 433 MHz
Transmission Distance: 3 meters (without antenna) to 100 meters (maximum)
Rs 390.00
Quick Info :
MFRC522 chip based board
Operating frequency: 13.56MHz
Supply Voltage: 3.3V
Current: 13-26mA
Rs 360.00Rs 430.00
Quick Info :
The working voltage: 5 ~ 12V
Output amplitude: 4.2V V-PP(5v input) to 11.4V V-PP(12V input).
Maximum output current: >=15mA (5V IN), >=35mA (12V IN)
Rs 220.00Rs 290.00
Quick Info :
Operating voltage : 2.3V – 5.5V
Battery not included
Battery : CR2032
Rs 590.00
Quick Info:
Onboard chip AT24C256 chip
Onboard the I2C communications required pull-up resistor
All pins are leads and marked
PCB board Dimensions : 36.5 (mm) x12 (mm)
Rs 200.00Rs 390.00
Quick Info :
All SD SPI pins output, MOSI, SCK, MISO, and CS.
Support 5V/3.3V input.
This module can handle 2GB SD cards.
Rs 350.00
Quick Info:
Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Size: 45 x 28mm
Net weight: 6g
Rs 350.00
Quick Info :
Acrylic Body.
Easy to install.
Compatible with HC-SR04
Rs 130.00
Quick Info :
Name: TT motor
Type: 1:48
Speed: 45±10%r/min 90±10%r/min
Rated voltage: 3V/6V
Rs 350.00
Quick Info :
Channel : 4
Coil sensitivity = 5VDC
Maximum Contact capacity = 250VAC/10VDC
Maximum Current capacity = 10A
Rs 560.00Rs 790.00
Quick Info :
Channel : 1
Coil sensitivity = 5VDC
Maximum Contact capacity = 250VAC/10VDC
Maximum Current capacity = 10A
Rs 190.00Rs 290.00
Quick Info :
Channels : 1
Input release voltage: 3.5 to 5V
Rated load voltage: 100V to 240V AC
Load current: 0.10 to 2A
Rs 860.00
Quick Info :
Arduino and Raspberry Pi compatible
4-key membrane switch pad has 5 pin female header on end of flat cable
White sticker on back can be peeled off for adhesive mounting
Rs 285.00
Quick Info :
Arduino and Raspberry Pi compatible
16-key membrane switch pad has 8 pin female header on end of flat cable
White sticker on back can be peeled off for adhesive mounting
Rs 290.00
Quick Info :
uses the 5050 full-color LED
Operating voltage: 5V
by adjusting the three primary colors can be mixed PWM get different colors
Rs 100.00
Quick Info :
Interface : I2C
I2C Address : 0x3F
Supply voltage : 5V
Contrast Adjust : Through Potentiometer
Backlight : Blue
Rs 1,100.00Rs 1,200.00
Rs 350.00
