Shop
Best Seller Items
-
-
Brass Threaded Insert Knurled M3
Quick Info :
- Thread: M3 (0.5mm pitch)
- Material: Knurled brass
- Type: Heat-set threaded insert
- Lengths: 3mm, 4mm, 5mm, 7mm
- Outer Diameter: 4.2mm, 4.5mm, 5mm
- Use: 3D printing, plastic enclosures, robotics assemblies
Price range: Rs 10.00 through Rs 20.00Brass Threaded Insert Knurled M3
Price range: Rs 10.00 through Rs 20.00 -
M2 Phillips Head Bolts with Nuts
Quick Info :
- Size: M2 Thread
- Available Lengths: 4mm, 6mm, 8mm, 12mm, 16mm, 25mm
- Material: Stainless Steel
- Head Type: Phillips
- Includes: Bolt + Nut
Price range: Rs 10.00 through Rs 15.00M2 Phillips Head Bolts with Nuts
Price range: Rs 10.00 through Rs 15.00 -
M3 Phillips Head Bolts with Nuts
Quick Info :
- Size: M3 Thread
- Available Lengths: 4mm, 6mm, 8mm, 10mm, 12mm, 16mm, 20mm, 25mm, 30mm
- Material: Stainless Steel
- Head Type: Phillips
- Includes: Bolt + Nut
Price range: Rs 10.00 through Rs 40.00M3 Phillips Head Bolts with Nuts
Price range: Rs 10.00 through Rs 40.00 -
Male-Female Jumper Wire 30cm
Quick Info :
- Connector Type : Male to Female
- Wire Length : 30cm
- Pin Pitch : 2.54mm
- Wire Gauge : 24AWG
Rs 8.00Male-Female Jumper Wire 30cm
Rs 8.00 -
JST XH 2.54mm Connector Cable and Base 2 – 12 Pin
Quick Info:
- Type: JST-XH 2.54mm
- Pins: 2P – 12P options
- Cable: 200mm, 26AWG
- Current: 3A per pin
- Includes: Male + Female pair
Price range: Rs 25.00 through Rs 90.00
-
LM35DZ Temperature Sensor IC
Quick Info :
- Operating Voltage : 4V to 30V DC
- Output Voltage : 0 mV + (10 mV/°C × Temperature)
- Temperature Range : -55°C to +150°C
- Accuracy : ±0.5°C at 25°C
- Linear Scale Factor : 10 mV/°C
- Response Time : Typically less than 1 second
Rs 200.00LM35DZ Temperature Sensor IC
Rs 200.00 -
GP Alkaline Batteries 12V GP27A
Quick info :
Battery Size: 27A
Voltage: 12V
Capacity: 18mAh
Chemistry: AlkalineRs 200.00Rs 250.00GP Alkaline Batteries 12V GP27A
Rs 200.00Rs 250.00 -
IRF3205 HEXFET Power MOSFET 55V 110A
Quick Info :
- N-Channel Power MOSFET
- Continuous Drain Current (ID) is 110A when VGS is 10V
- Minimum Gate threshold voltage 2V
- Drain to Source Breakdown Voltage: 55V
- Low On-Resistance of 8.0mΩ
- Gate-Source Voltage is (VGS) is ±20V
Rs 200.00IRF3205 HEXFET Power MOSFET 55V 110A
Rs 200.00 -
Heat Shrink Tubing 1mm – 28mm
Quick Info :
- Type: Heat Shrink Tubing (Polyolefin)
- Sizes: 1mm to 28mm (before shrinking)
- Shrink Ratio: 2:1 (50% reduction)
- Temperature: Operating -55°C to +125°C
- Use: Wire insulation, cable repair, solder joints, bundling
Price range: Rs 20.00 through Rs 200.00Heat Shrink Tubing 1mm – 28mm
Price range: Rs 20.00 through Rs 200.00 -
XT60 Connector Pair Male & Female
Quick Info:
- Connector Type : XT60 (Male & Female pair)
- Rated Current : 60A continuous
- Contact Material : Gold-plated copper
- Housing Material : Nylon (high-temperature resistant)
- Locking Mechanism : Self-locking, polarity-keyed
Rs 200.00XT60 Connector Pair Male & Female
Rs 200.00 -
Sound Sensor Module
Quick Info :
- Operating voltage : 3.3 V
- Operating current : 4~5 mA
- Signal to noise ratio : 54 dB
Rs 200.00 -
NRF24L01 2.4GHz Transceiver Adapter Base
Quick Info :
- It can be used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
Rs 200.00Rs 250.00NRF24L01 2.4GHz Transceiver Adapter Base
Rs 200.00Rs 250.00 -
AT24C256 I2C interface EEPROM Memory Module
Quick Info:
- Onboard chip AT24C256 chip
- Onboard the I2C communications required pull-up resistor
- All pins are leads and marked
- PCB board Dimensions : 36.5 (mm) x12 (mm)
Rs 200.00Rs 390.00AT24C256 I2C interface EEPROM Memory Module
Rs 200.00Rs 390.00 -
Keypad Flexible 16 Keys
Quick Info :
- Arduino and Raspberry Pi compatible
- 16-key membrane switch pad has 8 pin female header on end of flat cable
- White sticker on back can be peeled off for adhesive mounting
Rs 200.00Rs 290.00Keypad Flexible 16 Keys
Rs 200.00Rs 290.00 -
KY-023 Dual-Axis XY Joystick Module
Quick Info:
- Input Voltage : 3.3V to 5V DC
- Output Signal : 2 analog (X, Y) + 1 digital (switch)
- Pin Interface : VCC, GND, VRx, VRy, SW
- Dimensions : 34mm x 26mm x 32mm
Rs 200.00Rs 250.00KY-023 Dual-Axis XY Joystick Module
Rs 200.00Rs 250.00 -
PCF8574 LCD to I2C Adapter Board
Quick Info :
- IC Chip : PCF8574 / PCF8574T
- Compatible Displays : 1602 (16×2) & 2004 (20×4) LCD Modules
- I2C Address : 0x20 to 0x27 (jumper selectable)
- Operating Voltage : 2.5V to 6V
Rs 200.00Rs 390.00PCF8574 LCD to I2C Adapter Board
Rs 200.00Rs 390.00 -
MAX485 RS485 to TTL Converter Module
Quick Info :
- IC Chipset : MAX485
- Operating Voltage : 5V DC
- Communication Standard : RS-485 (EIA-485)
- Max Nodes on Bus : 32 Transceivers
- Max Communication Distance : Up to 1200m
Rs 200.00Rs 220.00MAX485 RS485 to TTL Converter Module
Rs 200.00Rs 220.00 -
18650 2S PCB Battery Holder BK-18650-PC4
Quick Info :
- Model: BK-18650-PC4
- Cells: 2 × 18650 (2S series)
- Voltage Output: 7.4V nominal
- Mounting: PCB through-hole
- Contacts: Spring-loaded
- Material: Flame-retardant plastic
- Current: Up to 5A continuous
Rs 190.00Rs 220.0018650 2S PCB Battery Holder BK-18650-PC4
Rs 190.00Rs 220.00 -
GT2 20T Timing Pulley 8mm Bore
Quick Info :
- Type : GT2 Pulley
- Teeth : 20T
- Bore : 8mm
- Material : Aluminum Alloy
Rs 190.00Rs 250.00GT2 20T Timing Pulley 8mm Bore
Rs 190.00Rs 250.00 -
-
Right Angle PCB Terminal Connector 5.08mm
Quick Info :
- Pitch : 5.08mm
- Pin Count : 2 to 12
- Connection : Screw Clamp, Pluggable
- Rated Current : 10A
- Rated Voltage : 250V AC/DC
- Wire Range : 24 to 12 AWG (0.2 to 2.5mm²)
Price range: Rs 40.00 through Rs 190.00Right Angle PCB Terminal Connector 5.08mm
Price range: Rs 40.00 through Rs 190.00 -
KY-005 IR Transmitter Module
Quick Info :
- Operating Voltage: 5V
- Current Consumption: 30-60mA
- Frequency: 38kHz
- Wavelength: 940nm
Rs 190.00Rs 220.00KY-005 IR Transmitter Module
Rs 190.00Rs 220.00 -
WS2812B 5050 RGB LED Module 1-Bit 5V Square
Quick Info:
- LED Type : WS2812B 5050 SMD RGB
- Number of LEDs : 1
- Interface : Single-Wire Data (DIN / DOUT)
- Operating Voltage : 5V DC
- Current Consumption : 60mA (Max)
Rs 180.00Rs 200.00WS2812B 5050 RGB LED Module 1-Bit 5V Square
Rs 180.00Rs 200.00 -
WS2812B 5050 RGB LED Module 2×2 4-Bit 5V
Quick Info:
- LED Type : WS2812B 5050 SMD RGB
- Number of LEDs : 4 (2×2 Layout)
- Interface : Single-Wire Data (DIN / DOUT)
- Operating Voltage : 5V DC
- Current Consumption : 60mA per LED (Max)
Rs 180.00Rs 200.00WS2812B 5050 RGB LED Module 2×2 4-Bit 5V
Rs 180.00Rs 200.00 -
TXS0108E 8CH Logic Level Converter 1.2V to 5.5V
Quick Info:
- IC : TXS0108E
- Channels : 8 (all bi-directional, full-duplex)
- VCCA (A side) : 1.2V – 3.6V (low voltage)
- VCCB (B side) : 1.65V – 5.5V (high voltage)
- Max Speed (Push-Pull) : 110Mbps
- Max Speed (Open-Drain) : 1.2Mbps
- Direction Sensing : Automatic (no DIR pin)
- Protocols : UART / SPI / I²C / GPIO / SD card
- Pin Pitch : 2.54mm breadboard compatible
- Compatible : Arduino / ESP32 / Raspberry Pi / STM32
Rs 180.00Rs 220.00TXS0108E 8CH Logic Level Converter 1.2V to 5.5V
Rs 180.00Rs 220.00 -
Bulb Socket Holder with Wire 1156 BA15S P21W
Quick Info:
- Socket Type : BA15S single contact bayonet
- Compatible Bulbs : P21W, 1156, 382, 7506 & equivalents
- Wire Leads : 2 wires (~10–15cm)
- Operating Voltage : 6V / 12V DC
- Applications : Reversing, brake, indicator, tail lights
Rs 180.00Rs 250.00Bulb Socket Holder with Wire 1156 BA15S P21W
Rs 180.00Rs 250.00 -
HX1838 IR Remote Control Module
Quick Info:
- Receiver IC : HX1838
- Supply Voltage : 2.7V – 5.5V
- Carrier Frequency : 38 kHz
- Interface : 3-Pin (VCC, GND, OUT)
- Protocol Support : NEC, RC5, RC6 and others
Rs 180.00Rs 200.00HX1838 IR Remote Control Module
Rs 180.00Rs 200.00 -
KY-039 Heartbeat Sensor Module
Quick Info:
- Operating Voltage : 3.3V – 5V DC
- Output Type : Analog
- Sensing Method : IR LED + Phototransistor
- Detection : Fingertip PPG
- Pin Count : 3 (Signal, VCC, GND)
- Onboard Resistor : Yes
- Compatible With : Arduino, Raspberry Pi, ESP32
Rs 180.00Rs 200.00KY-039 Heartbeat Sensor Module
Rs 180.00Rs 200.00 -
KY-035 Analog Hall Magnetic Sensor Module
Quick Info:
- Sensor Type : Hall Effect (Analog)
- Sensor IC : SS49E
- Output Type : Analog Voltage
- Operating Voltage : 3.3V – 5V DC
- Magnetic Flux Range : -70mT to +70mT (typical)
- Pins : 3 (Signal, VCC, GND)
Rs 180.00Rs 250.00KY-035 Analog Hall Magnetic Sensor Module
Rs 180.00Rs 250.00 -
T10 W5W RGB 12SMD COB LED Bulb
Quick Info:
- Bulb Type : T10 / W5W Wedge
- LED Chip : 12SMD COB
- Colour : RGB Multi-Colour
- Light Effect : Dynamic Colour Cycling
- Voltage : 12V DC
- Application : Dashboard, Interior, Side Marker
Rs 180.00Rs 200.00T10 W5W RGB 12SMD COB LED Bulb
Rs 180.00Rs 200.00 -
Rigid Shaft Coupler
Quick Info:
- Material : Aluminium Alloy
- Available Sizes : 4mm–6mm, 4mm–8mm, 5mm–5mm, 5mm–8mm, 6mm–6mm, 6mm–8mm, 8mm–8mm
- Fixing Method : Dual Set Screws
- Backlash : Zero
- Application : CNC, 3D Printers, Robotics
Rs 180.00Rigid Shaft Coupler
Rs 180.00 -
DC Motor Brushed FF 180 4.5V 6000RPM
Quick Info :
- Voltage : 4.5V
- Speed : 6000 RPM
- Type : Brushed Motor
- Size : FF180
Rs 180.00Rs 250.00DC Motor Brushed FF 180 4.5V 6000RPM
Rs 180.00Rs 250.00 -
M12 Metal Push Button Momentary 12mm
Quick Info :
- Size: 12mm
- Type: Momentary
- Material: Stainless Steel
- Waterproof: Yes
- Voltage: 12V – 24V DC
Rs 180.00Rs 200.00M12 Metal Push Button Momentary 12mm
Rs 180.00Rs 200.00 -
Vibration Sensor Module SW-420
Quick Info :
- Type: Vibration/Shock Sensor
- Voltage: 3.3V – 5V
- Output: Digital
- Sensitivity: Adjustable
- Chip: LM393 Comparator
Rs 180.00Rs 200.00Vibration Sensor Module SW-420
Rs 180.00Rs 200.00 -
GT2 20T Timing Pulley 6mm Bore
Quick Info :
- Teeth: 20T GT2
- Bore Size: 6mm
- Material: Anodized aluminum
- Application: 3D printers/CNC
Rs 180.00Rs 350.00GT2 20T Timing Pulley 6mm Bore
Rs 180.00Rs 350.00 -
Extruder Drive Wheel 40 Teeth 5mm Inner Hole Diameter
Quick Info :
- Teeth: 40
- Bore: 5 mm
- Material: Brass
- Filament: 1.75 mm
- Application: 3D Printer Extruder
Rs 180.00Rs 280.00Extruder Drive Wheel 40 Teeth 5mm Inner Hole Diameter
Rs 180.00Rs 280.00 -
N20 Ball Caster Wheel 3PI 15mm
Quick Info :
- Type: Ball Caster Wheel
- Ball Material: 304 Stainless Steel
- Dimensions: 22mm x 15mm
- Weight: 10g
- Application: Mini robots, RC cars
Rs 180.00Rs 250.00N20 Ball Caster Wheel 3PI 15mm
Rs 180.00Rs 250.00 -
12V LED Panel Indicator Lights IP65 10MM
Quick Info :
- Type: LED Panel Indicator
- Voltage: 12V DC
- Mounting Size: 10mm
- Colors: Red, Green, Blue, White
Rs 180.00Rs 200.0012V LED Panel Indicator Lights IP65 10MM
Rs 180.00Rs 200.00 -
5V Step-Up Power Module Board 134N3P
Quick Info :
- BAT Discharging Stop Voltage: 2.9V.
- Discharging Efficiency:85%(input 3.7V output 5V/1A).
- Charging and discharging indication.
- Internally installed charging and discharging power MOS.
Rs 180.00Rs 200.005V Step-Up Power Module Board 134N3P
Rs 180.00Rs 200.00 -
Flame Sensor Module 4 Pin
Quick Info :
- Type: Flame Detection Module
- Voltage: 3.3–5V
- Outputs: Analog + Digital
- Pins: 4-Pin Interface
- Use: Fire detection, safety projects
Rs 180.00Rs 280.00Flame Sensor Module 4 Pin
Rs 180.00Rs 280.00
