Skip to content
Quick Info :
Type : GT2 Pulley
Teeth : 20T
Bore : 8mm
Material : Aluminum Alloy
Rs 190.00Rs 250.00
Quick Info :
Type: Microwave Radar Motion Sensor
Voltage: 4-28V DC
Range: 5-7 meters
Output: 3.3V Digital
Detection: 360° Omnidirectional
Rs 190.00Rs 300.00
Quick Info :
Model: BK-18650-PC4
Cells: 2 × 18650 (2S series)
Voltage Output: 7.4V nominal
Mounting: PCB through-hole
Contacts: Spring-loaded
Material: Flame-retardant plastic
Current: Up to 5A continuous
Rs 190.00Rs 220.00
Quick Info :
IC Chipset : MAX485
Operating Voltage : 5V DC
Communication Standard : RS-485 (EIA-485)
Max Nodes on Bus : 32 Transceivers
Max Communication Distance : Up to 1200m
Rs 200.00Rs 220.00
Quick Info :
IC Chip : PCF8574 / PCF8574T
Compatible Displays : 1602 (16×2) & 2004 (20×4) LCD Modules
I2C Address : 0x20 to 0x27 (jumper selectable)
Operating Voltage : 2.5V to 6V
Rs 200.00Rs 390.00
Quick Info :
Driver IC : TM1637
Display Type : 4-digit 7-segment LED
Digit Size : 0.36 inch
Interface : 2-wire serial (CLK, DIO)
Operating Voltage : 3.3V to 5V DC
Rs 200.00Rs 390.00
Quick Info:
Input Voltage : 3.3V to 5V DC
Output Signal : 2 analog (X, Y) + 1 digital (switch)
Pin Interface : VCC, GND, VRx, VRy, SW
Dimensions : 34mm x 26mm x 32mm
Rs 200.00Rs 250.00
Quick Info :
Arduino and Raspberry Pi compatible
16-key membrane switch pad has 8 pin female header on end of flat cable
White sticker on back can be peeled off for adhesive mounting
Rs 200.00Rs 290.00
Quick Info:
Onboard chip AT24C256 chip
Onboard the I2C communications required pull-up resistor
All pins are leads and marked
PCB board Dimensions : 36.5 (mm) x12 (mm)
Rs 200.00Rs 390.00
Quick Info :
It can be used with NRF24L01 wireless module
Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
Allows for easy connection to nRF24L01+ modules
Small power on SMD LED indicator
Rs 200.00Rs 250.00
Quick Info :
Input voltage: 7-12 V (DC) or 5V USB power supply.
Output voltage: 3.3V and 5V can switch over.
Maximum output current: <700 mA.
Rs 200.00Rs 280.00
Quick Info
Working voltage : 5V
Output format : Digital switching output (0 and 1), and analog voltage output AO
Potentiometer adjust the sensitivity
Uses a wide voltage LM393 comparator
Rs 200.00Rs 230.00
Quick Info :
Operating voltage : 3.3 V
Operating current : 4~5 mA
Signal to noise ratio : 54 dB
Rs 200.00
Quick Info:
Connector Type : XT60 (Male & Female pair)
Rated Current : 60A continuous
Contact Material : Gold-plated copper
Housing Material : Nylon (high-temperature resistant)
Locking Mechanism : Self-locking, polarity-keyed
Rs 200.00
Quick Info :
Type: Solderless Breadboard
Tie Points: 400
Rows & Columns: 2 Power Rails + 30 Rows (5 Points per Row)
Pitch: 2.54mm (0.1 inch)
Material: ABS plastic with nickel-plated contacts
Rs 200.00
Quick Info :
Operating Voltage : 3V – 6V DC
Gear Ratio : 1:48
No-Load Speed : 90 RPM @ 3V / 200 RPM @ 6V
Stall Torque : 0.8 kg·cm @ 6V
Stall Current : ~1.5A @ 6V
Shaft : 5.3mm dia × 10mm (dual shaft)
Body Dimensions : 70 × 22 × 19mm
Weight : 30.6g
Compatible Drivers : L298N / L293D / TB6612FNG / DRV8833
Rs 200.00Rs 250.00
Quick Info :
Dimensions: 100mm X 60mm X 27mm
Rs 200.00
Quick Info :
N-Channel Power MOSFET
Continuous Drain Current (ID) is 110A when VGS is 10V
Minimum Gate threshold voltage 2V
Drain to Source Breakdown Voltage: 55V
Low On-Resistance of 8.0mΩ
Gate-Source Voltage is (VGS) is ±20V
Rs 200.00