Best Seller Items
-
Raspberry Pi 4 Model B Original
Quick Info :
- Processor: Quad-core 1.5GHz ARM Cortex-A72
- RAM: 2GB / 4GB / 8GB options
- Display: Dual 4K support
- Connectivity: Dual-band WiFi, Bluetooth 5.0, Gigabit Ethernet
- USB: 2×USB 3.0, 2×USB 2.0
Rs 23,950.00 – Rs 35,000.00Raspberry Pi 4 Model B Original
Rs 23,950.00 – Rs 35,000.00 -
Gordak 952 Soldering Station with Hot Air Gun
Quick Info :
- Dual Display
- Soldering Iron – 60W
- Hot Air Gun – 270W
Rs 29,500.00Gordak 952 Soldering Station with Hot Air Gun
Rs 29,500.00 -
30VDC 5A Professional Adjustable Bench Power Supply
Quick Info :
- Type: Metal Case
- Input Voltage: 230VAC
- Output Voltage: 0-30VDC
- Output Current: 5A (max
Rs 19,990.0030VDC 5A Professional Adjustable Bench Power Supply
Rs 19,990.00 -
Rework Station 8586D
Quick Info :
- Voltage: 220V / 50Hz
- Power Consumption: 750W (maximum)
- Temperature Range:
- Hot Air Gun: 100°C to 450°C
- Soldering Iron: 200°C to 480°C
- Airflow: Up to 120 liters per minute
- Dimensions: 14.6 x 9 x 13 cm
- Weight: 2.1 kg
Rs 16,500.00Rs 18,500.00Rework Station 8586D
Rs 16,500.00Rs 18,500.00 -
600W AC to DC Converter Adjustable Variable Power Supply 0-15VDC 0-50A
Quick Info :
- Dual adjustable controls: 0-15V DC voltage, 0-50A current
- High power capacity: 600W maximum output
- LCD display for real-time voltage and current monitoring
- Selectable input: 110 or 240V AC worldwide compatibility
- Independent voltage and current control knobs
- Multiple safety protections: overload, overvoltage, short-circuit
- Professional grade for lab testing and high-power applications
Rs 14,000.00Rs 15,500.00600W AC to DC Converter Adjustable Variable Power Supply 0-15VDC 0-50A
Rs 14,000.00Rs 15,500.00 -
MQ138 VOC Gas Sensor
Quick Info :
- Sensor Type: VOC Gas Sensor
- Model: MQ138
- Detection Range: 5-500 ppm
- Heater Voltage: 5.0V DC or AC
- Applications: Gas Alarms, Portable Detectors
Rs 10,500.00Rs 10,900.00MQ138 VOC Gas Sensor
Rs 10,500.00Rs 10,900.00
-
DS1302 Real Time Clock Module
Quick Info
- Supply voltage (typically): 3.3V
- Battery not included
- Battery : CR2032
Rs 790.00DS1302 Real Time Clock Module
Rs 790.00 -
GY-BMI160 Module 6DOF 6 Axis Gyroscope
Quick Info :
- Power supply: 3-5v (Recommended 3.3v)
- Communication mode: Standard IIC/SPI communication protocol
- Chip built in AD 16bit converter, 16 bit data output
- Gyro range: ±125 ±250 ±500 ±1000 ±2000 degrees /s
Rs 750.00GY-BMI160 Module 6DOF 6 Axis Gyroscope
Rs 750.00 -
3 Channel Line TCRT5000 Tracking Module
Quick Info :
- This infrared sensor trio detector and trio output
- Build-in TCRT5000 sensor
- Number of channels : 3
Rs 750.003 Channel Line TCRT5000 Tracking Module
Rs 750.00 -
Bluetooth XBee Shield V3 Module Wireless Control
Quick Info :
- Stackable design, easy to plug into the ARDUINO development board.
- Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
- Coupled with the XBee module, you can achieve two or more sets of communication between Arduino or Arduino and PC Communications.
Rs 750.00 -
LiPo Battery 3.7V 250mAh
Quick Info :
- Battery Type : Lithium Polymer (LiPo)
- Nominal Voltage : 3.7V DC
- Capacity : 250mAh
- Charging Voltage : 4.2V ± 0.05V
- Discharge Cutoff Voltage : ~3.0V
- Continuous Discharge Rate : ~1C – 2C
- Max Discharge Current : ~250mA – 500mA
Rs 690.00LiPo Battery 3.7V 250mAh
Rs 690.00 -
KW-401 Speaker 65W 4 inch
Quick Info :
- Model: KW-401
- Maximum Power: 130 Watts (MAX)
- Nominal Power: 65 Watts (RMS)
- Impedance: 40HM
- Frequency Response: 100 Hz – 18,000 Hz
- Material: Metal frame with paper cone
Rs 690.00KW-401 Speaker 65W 4 inch
Rs 690.00 -
5” Micro Nipper Cutting Tool
Quick Info :
- Length: 5 inches (125mm)
- Blade Material: Hardened Carbon Steel / Stainless Steel
- durable blades for clean and accurate cuts.
- Made from high-quality materials for long-lasting performance.
- Flush-cut or semi-flush (for clean, precise cuts)
Rs 690.005” Micro Nipper Cutting Tool
Rs 690.00 -
Digital Audio Power Amplifier Module HW-710
Quick info :
- Output Power: 2x50W (stereo mode) or 100W (mono mode)
- Frequency Response: 20Hz to 20kHz
- Signal-to-Noise Ratio (SNR): ≥100dB
- Chip: TPA3116D2
- Power Supply Voltage: 12-24V DC
Rs 690.00 -
SN65HVD230 CAN Module
Quick Info :
- Operates with a single 3.3 V Supply
- Bus Pin ESD Protection Exceeds ±16 kV HBM
- High Input Impedance Allows for Up to 120 Nodes on a Bus
Rs 690.00SN65HVD230 CAN Module
Rs 690.00 -
Inductive Proximity Sensor PNP PL-05P
Quick Info :
- Sensing distance : 5mm
- Operating voltage : 10 – 30 VDC
- Response frequency : 800Hz
- Output method : PNP, 150mA load
Rs 690.00Inductive Proximity Sensor PNP PL-05P
Rs 690.00 -
-
Wire Cutter Nipper 12
Quick Info :
- Size (L x B x H) : 15 cm x 5 cm x 2 cm
- Weight : 100 g
- Size : 6 Inch
Rs 690.00Wire Cutter Nipper 12
Rs 690.00 -
Arduino Compatible XD-204 Data Logger Shield
Quick Info :
- Real Time Clock Module : DS1307
- SD Card reader : standard SD card
- RTC battery included
Rs 690.00 -
Project Enclosure 115mm X 90mm X 55mm
Quick Info :
- Dimensions: 115mm X 90mm X 55mm
Rs 690.00Project Enclosure 115mm X 90mm X 55mm
Rs 690.00 -
GPS Adhesive Type Antenna SMA
Quick Info :
- Frequency – 1559MHz-1609Mhz
-
Active antenna noise figure <1.5dB
-
Polarization -RHCP or Linear
-
Cable length – Max. 3m
Rs 690.00GPS Adhesive Type Antenna SMA
Rs 690.00 -
-
-
ATTINY85-20PU Atmel
Quick Info :
- : 20MHz
- : 8KB
- : 512Byte
- : 8 Pins
Rs 690.00ATTINY85-20PU Atmel
Rs 690.00 - : 20MHz
-
-
LM2596 CC/CV Li-Ion Charger/LED Power Supply Module
Quick Info :
- Input Voltage: 5-35V
- Input Voltage Must Be At Least 2V Above Output Voltage
- Output Voltage: 1.25-30V (infinitely adjustable)
- Constant Current Range: 0-3A (infinitely adjustable)
Rs 690.00 -
Active GPS Patch Antenna (25*25)
Quick Info :
- Frequency – 1559Mhz-1609Mhz
- Active antenna noise figure < 1.5dB
- Cable – RF1.13
- Connector – I-PEX
Rs 650.00Active GPS Patch Antenna (25*25)
Rs 650.00 -
-
-
Wire Stripper 5 Inch RT125
Quick Info :
- Brand: R’DEER
- Model: RT-125F
- Size: 5 inches (125mm)
- Material: High-carbon steel with plastic-coated handles
- Stripping sizes ranging from AWG 30 to 10
- Cutting small wires and cables.
Rs 600.00Wire Stripper 5 Inch RT125
Rs 600.00 -
LCD 16X2 Keypad Shield
Quick Info :
- Operating Voltage: 5V
- 5 Push buttons.
- Left, Right, Up, Down and Select buttons
- Screen contrast adjustment
- Arduino Reset button
Rs 595.00LCD 16X2 Keypad Shield
Rs 595.00 -
6 Ohms 15W Speaker 3 Inch
Quick Info :
- Impedance: 6 Ω
- Rated Power Handling: 15 W
- Magnet type : Double Magnet
- Frequency Response: 108 Hz – 20 kHz
- Speaker Diameter: 3 inches (78 mm)
- Mounting Depth: 52 mm
Rs 590.006 Ohms 15W Speaker 3 Inch
Rs 590.00 -
BMS 3S 40A Li-ion Battery Protection Board
Quick info :
- Applicable voltage: 12V
- Charge current: 20A (Max)
- Discharge current: 40A
- Overdischarge protection voltage: 2.5V ± 0.05V per cell
- Overcharge protection voltage: 4.25V ± 0.05V per cell
Rs 590.00 -
Project Enclosure 80mm X 80mm X 60mm
Quick Info :
- Dimensions: 80mm X 80mm X 60mm
Rs 590.00Project Enclosure 80mm X 80mm X 60mm
Rs 590.00 -
MAX30102 Pulse Oximeter & Heart-Rate Module
Quick Info :
- LED Peak Wavelength: 660nm/880nm
- LED Supply Voltage: 3.3~5V
- Interface: I2C Interface
- Operating Temperature Range: -40°C to +85°C
Rs 490.00 – Rs 590.00 -
MAX7219 8 Way Display Module
Quick Info :
- Eight 7-Segment LED Displays with 0.36″ high red digits
- LED displays mounted in sockets
- Built-in MAX7219 LED Driver
- SPI 3-wire serial interface for easy hookup to MCU
- Can daisy-chain multiple modules together for larger displays
Rs 590.00MAX7219 8 Way Display Module
Rs 590.00 -
OV7670 Camera Module
Quick Info :
- Resolution 640×480 VGA
- Flicker (50/60 Hz) auto detection
- Onboard regulator, only single 3.3V supply needed
Rs 590.00Rs 925.00OV7670 Camera Module
Rs 590.00Rs 925.00 -
TDA7297 15+15W Dual Bridge Amplifier Module
Quick Info:
- Working voltage: 6 to 18V
- Dual channel 15W+15W
- on-board dial potentiometer
Rs 590.00
