Best Seller Items
-
-
Jumper Wire Male-Female 30cm
Quick Info :
- Connector : Male to Female
- 1 Cable : Rs. 8
- 1 Set (40pcs) : Rs. 320
Rs 8.00Jumper Wire Male-Female 30cm
Rs 8.00 -
Jumper Wire Male-Male 20cm
Quick Info :
- Connector : Male to Male
- 1 Cable : Rs. 6
- 1 Set (40pcs) : Rs. 240
Rs 6.00Jumper Wire Male-Male 20cm
Rs 6.00 -
Jumper Wire Male-Female 20cm
Quick Info :
- Connector : Male to Female
- 1 Cable : Rs. 6
- 1 Set (40pcs) : Rs. 240
Rs 6.00Jumper Wire Male-Female 20cm
Rs 6.00 -
LED 5mm Bulb Common Anode
Specification:
- 5mm Round Standard Directivity
- Color : Red, Blue, Green, White, Yellow
- UV Resistant : Eproxy
- Forward Current (IF): 30mA
- Forward Voltage (VF): 1.8V to 2.4V
Rs 4.00LED 5mm Bulb Common Anode
Rs 4.00 -
Jumper Wire Male-Male 30cm
Quick Info :
- Connector : Male to Male
- 1 Cable : Rs. 8
- 1 Set (40pcs) : Rs. 320
Rs 8.00Jumper Wire Male-Male 30cm
Rs 8.00
-
360 Degree Rotary Encoder Module
Quick Info :
- Incremental Encoder
- Supply Voltage: 3-5V
- Left/Right rotary output pulse, each circle with 20 pulse
- Built in 10k resistor
- Cycles per revolution (CPR): 20
Rs 350.00360 Degree Rotary Encoder Module
Rs 350.00 -
1K – 100K Potentiometer
Quick Info :
- 1K, 5K, 10K, 50K, 100K Ohm
- Linear taper, carbon film type
- Single-Turn
Rs 30.00 – Rs 100.001K – 100K Potentiometer
Rs 30.00 – Rs 100.00 -
ESP8266 ESP-01 WIFI module
Quick Info :
- 802.11 b/g/n
- Operating Voltage: 3.3V
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
Rs 490.00Rs 590.00ESP8266 ESP-01 WIFI module
Rs 490.00Rs 590.00 -
Nema23 Stepper Motor L-Type Mounting Bracket
Quick Info :
- Type: L-type 90° mounting bracket
- Compatible: Nema 23 stepper motors (57mm)
- Material: Aluminum alloy (anodized)
- Hole Pattern: 47.14mm × 47.14mm
- Color: Black
- Features: Ribbed reinforcement, multi-hole mounting
- Use: CNC, 3D printers, laser cutters, robotics
Rs 380.00Rs 450.00Nema23 Stepper Motor L-Type Mounting Bracket
Rs 380.00Rs 450.00 -
Nylon Plastic Standoff Female-Female M3
Quick Info :
- Thread Size : M3
- Material : Nylon Plastic
- Type : Female-Female Standoff
- Lengths Available : M3x5, M3x10
Rs 15.00 -
Nylon Plastic Standoff Male-Female M3
Quick Info :
- Thread Size : M3
- Material : Nylon Plastic
- Type : Male-Female Standoff
- Lengths Available : M3x5+6, M3x10+6
Rs 15.00 -
DC Motor Brushed FF 180 4.5V 6000RPM
Quick Info :
- Voltage : 4.5V
- Speed : 6000 RPM
- Type : Brushed Motor
- Size : FF180
Rs 180.00Rs 250.00DC Motor Brushed FF 180 4.5V 6000RPM
Rs 180.00Rs 250.00 -
GT2 Timing Belt 10mm Width 300mm Length
Quick Info :
- Width : 10 mm
- Length : 300 mm
- Pitch : 2 mm
- Type : Closed Loop
Rs 400.00Rs 500.00GT2 Timing Belt 10mm Width 300mm Length
Rs 400.00Rs 500.00 -
N20 Mini Metal Gear Motor 6V 300RPM
Quick Info :
- Motor Type : DC Micro Gear Motor (N20)
- Rated Voltage : 6V DC
- No Load Speed : 300 RPM
- Shaft Type : D-Shaped Shaft
- Shaft Diameter : 3mm
- Shaft Length : 10mm
Rs 700.00Rs 800.00N20 Mini Metal Gear Motor 6V 300RPM
Rs 700.00Rs 800.00 -
Thermal Printer Paper Roll 58mm 57x30mm
Quick Info :
- Paper Type : Thermal Paper
- Paper Width : 58mm
- Roll Size : 57x30mm
- Core Diameter : Standard (Approx. 12mm)
Rs 250.00Rs 350.00Thermal Printer Paper Roll 58mm 57x30mm
Rs 250.00Rs 350.00 -
221 Series Lever Nut Wire Connectors Wago
Quick Info :
- Brand: Wago
- Series: 221 Lever Connectors
- Variants: 2-Port / 3-Port / 5-Port
- Wire Range: 0.14-4.0mm² (AWG 28-12)
- Rating: 450V / 32A
- Technology: Spring terminal
- Reusable: Unlimited cycles
Rs 140.00 – Rs 240.00221 Series Lever Nut Wire Connectors Wago
Rs 140.00 – Rs 240.00 -
GT2 Timing Belt 6mm Width 300mm Length
Quick Info :
- Belt Type : GT2 Timing Belt (Closed Loop)
- Width : 6mm
- Length : 300mm
- Pitch : 2mm
Rs 350.00Rs 450.00GT2 Timing Belt 6mm Width 300mm Length
Rs 350.00Rs 450.00 -
Type-C USB Connector Panel Mount
Quick Info :
- Connector Type : USB Type-C Female
- Mount Type : Panel Mount (Threaded with Nut)
- Cable Length : Approx. 20 cm
- Wire Type : Pre-soldered Red & Black Power Wires
- Protection : Waterproof Dust Cap Included
Rs 320.00Rs 500.00Type-C USB Connector Panel Mount
Rs 320.00Rs 500.00 -
Rechargeable Head Lamp Torch with Battery
Quick Info :
- Light Source : COB LED + High Power LED
- Lighting Modes : Top and Bottom
- Battery Type : Built-in Rechargeable Battery
- Charging Method : USB Charging
Rs 1,350.00Rs 1,500.00Rechargeable Head Lamp Torch with Battery
Rs 1,350.00Rs 1,500.00 -
SPL Series Lever Nut Wire Connectors
Quick Info :
- Series: SPL Lever Nut Connectors
- Variants: SPL2/3/4, SPL42, SPL62, SPL93
- Wire Range: 0.5-4.0mm² (AWG 24-12)
- Rating: 400V / 20-32A
- Installation: Push-in (solid) + Lever (stranded)
- Material: Polycarbonate housing, copper contacts
- Reusable: Yes (multiple cycles)
- Use: Electrical installations, lighting, junction boxes
Rs 80.00 – Rs 240.00 -
POM Pulley Plastic Wheel Bearing 625ZZ
Quick Info :
- Material: POM (Delrin) plastic wheel
- Bearing: 625ZZ (5×16×5mm)
- Bore: 5mm (625ZZ bearing)
- Wheel OD: 23-30mm (model dependent)
- Groove: Flat
- Use: Sliding doors, drawers, conveyors, linear guides
Rs 250.00Rs 300.00POM Pulley Plastic Wheel Bearing 625ZZ
Rs 250.00Rs 300.00 -
Flange Ball Bearing Miniature Deep Groove
Quick Info :
- Type: Flange deep groove ball bearing
- Variants: 623ZZ / 625ZZ / 628ZZ
- Seal: Double metal shield (ZZ)
- Material: Chrome steel
- Flange: Integrated mounting flange
- Lubrication: Pre-greased, maintenance-free
- Use: 3D printers, robotics, pulleys, conveyors
Rs 80.00 – Rs 120.00 -
ESP32 CAM Module with OV3660 Camera Module
Quick Info :
- Chip: ESP32 dual-core (240MHz)
- Memory: 4MB Flash, 520KB SRAM
- Camera: OV3660 3MP (up to 2048×1536)
- Storage: MicroSD card slot
- Connectivity: WiFi 802.11n + Bluetooth 4.2
- Frame Rate: Up to 60fps at VGA
- Programming: Arduino IDE, ESP-IDF (requires USB-TTL adapter)
- Power: 5V DC
- Note: External programmer required
Rs 2,250.00Rs 2,750.00ESP32 CAM Module with OV3660 Camera Module
Rs 2,250.00Rs 2,750.00 -
Lever Wire Connector Terminal Block 2-5 Ports
Quick Info :
- Series: 222-415 Lever Connectors
- Variants: 2-Port / 3-Port / 4-Port / 5-Port
- Wire Range: 0.08-4.0mm² (AWG 28-12)
- Rating: 400V / 32A
- Installation: Tool-free lever mechanism
- Material: Polycarbonate housing, copper contacts
- Reusable: Yes (multiple connect/disconnect cycles)
- Use: Lighting, electrical panels, junction boxes
Rs 30.00 – Rs 60.00Lever Wire Connector Terminal Block 2-5 Ports
Rs 30.00 – Rs 60.00 -
ESP32 S3 N16R8 Development Board with OV2640 Camera Module
Quick Info :
- Chip: ESP32-S3 dual-core (240MHz)
- Memory: 16MB Flash + 8MB PSRAM
- Camera: OV2640 2MP (up to 1600×1200)
- Storage: MicroSD card slot
- Connectivity: WiFi 802.11n + Bluetooth 5.0
- Frame Rate: Up to 60fps at VGA
- Programming: Arduino IDE, ESP-IDF, MicroPython
- Use: Smart cameras, surveillance, recording, AI vision
- Power: 5V USB Type-C/Micro-USB
Rs 3,950.00Rs 4,200.00ESP32 S3 N16R8 Development Board with OV2640 Camera Module
Rs 3,950.00Rs 4,200.00 -
DVI to HDMI Converter Adapter Module
Quick Info :
- Type: DVI-D ↔ HDMI passive adapter
- Direction: Bidirectional
- Resolution: Up to 1080p Full HD
- Audio: Not supported
- Power: None required (passive)
- Compatible: PC, Raspberry Pi, monitors, projectors
- Signal: Digital video only
Rs 550.00Rs 650.00DVI to HDMI Converter Adapter Module
Rs 550.00Rs 650.00 -
Matrix Keypad Plastic 4×4 16 Keys
Quick Info :
- Type: Hard plastic push button keypad
- Keys: 16 (0-9, *, #, A-D)
- Interface: 8 pins (4 rows + 4 columns)
- Pin Pitch: 2.54mm through-hole PCB
- Mounting: 4 corner mounting holes
- Housing: Black ABS plastic
- Compatible: Arduino, ESP32, Raspberry Pi
Rs 800.00Rs 900.00Matrix Keypad Plastic 4×4 16 Keys
Rs 800.00Rs 900.00 -
Matrix Keypad Plastic 3×4 12 Keys
Quick Info :
- Type: Hard plastic push button keypad
- Keys: 12 (0-9, *, #)
- Interface: 7 pins (4 rows + 3 columns)
- Pin Pitch: 2.54mm through-hole PCB
- Mounting: 4 corner mounting holes
- Housing: Black ABS plastic
- Compatible: Arduino, ESP32, Raspberry Pi
Rs 750.00Rs 850.00Matrix Keypad Plastic 3×4 12 Keys
Rs 750.00Rs 850.00 -
SSOP 16PIN/SOP 16PIN to DIP Adapter PCB Module
Quick Info :
- Input: SSOP-16 / SOP-16 SMD packages
- Output: DIP-16 (2.54mm pitch)
- SSOP Pitch: 0.635mm
- SOP Pitch: 1.27mm
- PCB: FR4, 1.6mm thickness
- Compatible: Breadboards, DIP sockets
- Use: SMD to through-hole conversion
Rs 50.00Rs 80.00SSOP 16PIN/SOP 16PIN to DIP Adapter PCB Module
Rs 50.00Rs 80.00 -
HC-020K Photoelectric Wheel Encoder Sensor Kit
Quick Info :
- Sensor Type: Infrared photoelectric encoder
- Resolution: 20 pulses per revolution
- Output: Digital TTL pulse
- Voltage: 3.3V – 5V DC
- Pins: VCC, GND, OUT (3-pin)
- Disk Slots: 20 slots
- Compatible: Arduino, ESP32, Raspberry Pi
Rs 420.00Rs 500.00HC-020K Photoelectric Wheel Encoder Sensor Kit
Rs 420.00Rs 500.00 -
Brushless Motor Driver Controller Board for Hard Drive BLDC Motor DC 7-12V
Quick Info :
- Input Voltage: DC 7V – 12V
- Current: ≤1.2A working / 1.5A max
- Motor Support: 3-wire & 4-wire BLDC
- Speed Control: Voltage-regulated
- Max Speed: ~10,000 RPM
- Detection: Auto 3/4-wire recognition
- Protection: Reverse polarity, over-current
- Size: 63mm × 45mm
Rs 980.00Rs 1,100.00Brushless Motor Driver Controller Board for Hard Drive BLDC Motor DC 7-12V
Rs 980.00Rs 1,100.00 -
A3144 Hall Effect Sensor Module 4 Pin
Quick Info :
- Sensor IC: A3144
- Output: Digital (active LOW) + Analog
- Voltage: 3.3V – 5V DC
- Pins: VCC, GND, DO, AO
- Detection: Unipolar (south pole)
- Range: Up to ~1cm
- Indicators: Power + Output LEDs
- Compatible: Arduino, Raspberry Pi, ESP32
Rs 280.00Rs 300.00A3144 Hall Effect Sensor Module 4 Pin
Rs 280.00Rs 300.00 -
RC Airplane Control Horn 19x17mm 4-Hole 1.4mm
Quick Info :
- Size: 19mm × 17mm
- Holes: 4 × 1.4mm diameter
- Material: Rigid nylon plastic
- Color: White
- Mount: Screw or adhesive
- Compatible: 0.8-1.4mm push rods
- Use: Aileron/elevator/rudder horns
- Aircraft: Universal fixed-wing RC
Rs 120.00Rs 150.00RC Airplane Control Horn 19x17mm 4-Hole 1.4mm
Rs 120.00Rs 150.00 -
RC Airplane Control Horn 16×17mm Plastic 3-Hole 1.6mm
Quick Info :
- Size: 16mm × 17mm
- Holes: 3 × 1.6mm diameter
- Material: Rigid nylon plastic
- Color: White
- Mount: Screw or adhesive
- Compatible: 1.0-1.6mm push rods
- Use: Aileron/elevator/rudder horns
- Aircraft: Universal fixed-wing RC
Rs 120.00Rs 150.00RC Airplane Control Horn 16×17mm Plastic 3-Hole 1.6mm
Rs 120.00Rs 150.00 -
Z Type Servo Push Rod Wire for RC Wing Airplane 190mm
Quick Info :
- Length: 190mm
- Diameter: 1.2mm steel wire
- End Type: Z-type bent ends
- Material: High-strength steel
- Compatible: SU27KT RC Fixed Wing
- Function: Servo push rod linkage
- Installation: Tool-free Z-bend fit
- Use: Aileron/elevator/rudder control
Rs 280.00Rs 350.00Z Type Servo Push Rod Wire for RC Wing Airplane 190mm
Rs 280.00Rs 350.00 -
USB to 12V DC Power Converter Cable
Quick Info :
- Input: 5V USB (Type-A)
- Output: 12V DC @ 1A (12W)
- Connector: DC barrel jack
- Type: Boost converter cable
- Cable Length: ~1 meter
- Protection: Over-current, short-circuit
- Use: Power 12V devices from USB
- Compatible: Power banks, USB adapters
Rs 550.00Rs 750.00USB to 12V DC Power Converter Cable
Rs 550.00Rs 750.00 -
PN532 NFC RFID Reader Writer Module
Quick Info :
- Chip: NXP PN532
- Frequency: 13.56MHz
- Range: 5-7cm read/write
- Interface: I2C/SPI/UART (selectable)
- Cards: Mifare, NTAG, NFC, FeliCa
- Voltage: 3.3V – 5V
- Compatible: Arduino, Raspberry Pi, ESP32
- Function: Read & Write NFC/RFID tags
Rs 1,150.00Rs 1,350.00PN532 NFC RFID Reader Writer Module
Rs 1,150.00Rs 1,350.00 -
18650 2S PCB Battery Holder BK-18650-PC4
Quick Info :
- Model: BK-18650-PC4
- Cells: 2 × 18650 (2S series)
- Voltage Output: 7.4V nominal
- Mounting: PCB through-hole
- Contacts: Spring-loaded
- Material: Flame-retardant plastic
- Current: Up to 5A continuous
Rs 190.00Rs 220.0018650 2S PCB Battery Holder BK-18650-PC4
Rs 190.00Rs 220.00 -
Raspberry Pi 4 Passive Aluminum Heatsink Case
Quick Info :
- Material: Aluminum alloy (184g)
- Cooling: Passive/fanless heatsink
- Compatible: Raspberry Pi 4B (all RAM)
- Color: Black anodized
- Features: No fan required, silent operation
- Includes: Case + 3 thermal pads
- GPIO: Cable interface reserved
Rs 2,300.00Rs 2,500.00Raspberry Pi 4 Passive Aluminum Heatsink Case
Rs 2,300.00Rs 2,500.00 -
Raspberry Pi Camera Module V1.3 5MP OV5647
Quick Info :
- Sensor: OV5647 5MP
- Still Images: 2592 × 1944 pixels
- Video: 1080p @ 30fps
- Interface: CSI (15-pin ribbon)
- Focus: Fixed (50cm to ∞)
- FOV: 67.9° diagonal
- Compatible: All Raspberry Pi with CSI port
- Version: V1.3
Rs 1,250.00Rs 1,550.00Raspberry Pi Camera Module V1.3 5MP OV5647
Rs 1,250.00Rs 1,550.00
